reflactaseal_product

ReflectASeal 550

Description:
REFLECTASEAL-550 is a high-solids polyamide-epoxy resin.  The formulation includes a long pot life as well as flexible properties, which allows it to withstand extreme abrasive conditions and a high tolerance to impact resistance.  REFLECTASEAL-550 is a metal primer developed specifically as a rust inhibitor for metal roof applications.

Application Areas:
REFLECTASEAL-550 is a protective coating for walls, tanks, pipes, floors, stairs, decks, equipment, and much more.  REFLECTASEAL-550 can be used where moist areas may prevent the use of other coatings.  REFLECTASEAL-550 is used in commercial and industrial surroundings.

 

Resistance:
REFLECTASEAL-550 has excellent resistance to various solvents, hydrocarbons, acids and alkalis.

 

Preparation:
To begin, the surface should be etched to provide a profile or “tooth” for optimal adhesion.  Surfaces must be cleaned free of grease, oil, wax, mastic compounds, paint, waterproofing compounds, form release materials, and all other contaminants prior to application.

Metal must be free of mill scale, rust, paint, oil, grease, oxides, etc.  An abrasive type of preparation is recommended to produce a profile for the REFLECTASEAL-550 to adhere to. The preparation procedures above are general guidelines. Detailed preparation methods are available through SSPC at www.sspc.org or 412-281-2331 or NACE at www.nace.org or 281-228-6200.

Mixing:
The mixing of parts A & B is very important!  REFLECTASEAL-550 has a mixing ratio of 3 parts “B” to 1 part “A”.  Use a power mixer to thoroughly combine both parts.  Mix for a minimum of 5 minutes.  Allow idle activation time for a minimum of 15 minutes.  Lacquer Thinner should only be added after the activation is complete.  For general purposes, no more than 1 quart per 4 gallons of solvent should be added to the mixture.

Application:
Brush, 3/8” nap roller cover, or airless spray equipment may be used to apply REFLECTASEAL-550.  Surface configuration, weather, or area surroundings will dictate application method.

DRY FILM APPLICATIONS
To get dry film of: Apply Sq. Ft. /gal
4 mils 300 sq ft
8 mils 150 sq ft
12 mils 100 sq ft

DO NOT apply product heavier than 100-sq. ft. per gallon per coat.  For a heavier dry film, apply necessary number of coats. Use of thinner increases possibility of sag and reduces dry film thickness.  REFLECTASEAL-550 may be applied to damp surfaces but it is best to have a dry surface if possible.

Allow REFLECTASEAL-550 to become tack-free before applying additional coats or approximately 6 hrs.  Caution!  Without the use of aggregate in REFLECTASEAL-550, the surface will be slippery when wet!

General:
REFLECTASEAL-550 should be applied in well-ventilated areas.  Surfaces should be free of foreign matter.  DO NOT apply product near an open flame.

Clean Up:
Application equipment should be cleaned immediately with Lacquer Thinner.  Use Apple Cider Vinegar to clean hands and skin.  Do not allow REFLECTASEAL-550 to remain on tools!  Once it sets and is cured, it is difficult to remove.

 

Flammability: Flammable during application.  Does not support combustion when cured.

Curing Time:
Pot Life: 3 hrs @ 80ºF
Drying Time: 6 hrs @ 80ºF
Total Cure: 36 hrs @ 80ºF

Packaging:
1-gallon units:
1 gal can containing 3 qt of Base    (part “B”)
1 qt can full, containing Activator    (part “A”)

20-gallon units:
4 – 6 gal pails containing 3¾ gals of Base    (part “B”)
1 – 6 gal pail containing 5 gals of Activator    (part “A”)

Colors:           REFLECTASEAL Standard Colors (Tan, Gray)

Solids Content:   85% Solids
Mixing Ratio:    3 parts B to 1 Part A (3:1)

Taber abraser CS-17 calibrase wheel at 4000 cycles with 1.3 mils wear and .22 grams lost.
Adhesion-Pull-Off (D4541):

Metal: 100% adhesion failure @ 2079 psi

Impact Resistance (D2794):

56 inch lbs. direct – passed

For further assistance, contact one of our technicians via phone or e-mail.

MSDS are available for health and safety data.

For emergency information contact:
CHEMTREC @ 1-800-424-9300

Safety:
This product (and any recommended thinner) contains solvents and/or chemical ingredients.  Adequate health and safety precautions should be observed during storage, handling, use, and drying periods.  For safe usage, user is specifically directed to consult the current Material Safety Data Sheet for this product.  When using this product in a confined space or closed area, consult the OSHA or ANSI bulletins on safety requirements.

The information as set forth in the technical data contained herein has been developed based on test and evaluations made by REFLECTASEAL, LLC for standard coating applications.  We believe this information is the best currently available on the subject.  We make no guarantee of results and assume no obligation or liability in connection with this information.  It is offered as possible helpful suggestion, any experimentation you may care to undertake along these lines, is at your own risk.  You should test the coating material to determine if it is suitable for the application intended.  It is supplied on the condition that you shall make your own tests to determine its suitability.  REFLECTASEAL, LLC shall have no liability for incidental or consequential damages, indirect or direct.  Our liability is limited to the net selling price of the purchased product(s) or the replacement of our product, at our option.